Linear Gate Installation Nationwide

Linear Gate Installation in Allen: What to Know First

Linear gate installation in Allen, TX typically runs $1,850 to $4,700 installed, depending on gate size, swing versus slide configuration, and whether we’re hanging a new gate or pairing a Linear operator with an existing one. We install and automate Linear driveway gates, pedestrian gates, sliding gates, swing gates, double gates, and security gates, and most standard installations are completed in one to two visits with the price settled before any work starts. Call (936) 274-8988 and a live person answers, 24 hours a day, every day of the week.

Call (936) 274-8988

This page is for Allen homeowners who already own a Linear product, or who are considering one, and want a gate hung and automated by people who know the brand well. Ironworks Gate Co. has been doing this since 1984. We’re an independent Linear service provider, which means we answer to you, not to a manufacturer’s call center.

Key Takeaways

• Linear gate installation in Allen typically costs between $1,850 and $4,700 installed.
• We install and automate single gates, double gates, slide gates, swing gates, and pedestrian gates with Linear operators.
• Most Linear installations are completed in one to two visits with no surprises on the bill.
• Every job is covered by our written 90-Day Done Right Promise, and we put it in writing on every single job, no exceptions.
• Call (936) 274-8988 any time, day or night, and a real person will answer.

How Linear Products Fail - and How We Fix Them

Linear builds solid, no-nonsense gate operators, but here’s what we see on driveways across Allen, from homeowners in Twin Creeks to Star Creek to the older streets off Bethany Drive.

• Linear PRO Access operators with limit switch drift. The PRO Access line, especially the LRA and PRO series slide gate operators, uses mechanical limit switches that can wander over time, especially with the freeze-thaw cycles we get in Collin County. The gate will stop three inches short of closed, or close and then reverse for no apparent reason. We realign the limit cams, verify the torque limiter, and reset the travel path so the gate seats fully every cycle. It’s a thirty-minute fix when you know what you’re looking at, and a mystery when you don’t.
• Linear swing gate operators with stripped drive gears. We see this on the Linear APC and LRA swing arm lines frequently, particularly on gates that get caught in the wind. The worm gear is softer than the gear it drives, which is by design, but it means the drive gear wears out long before the motor does. We replace the gear set with OEM or matching aftermarket parts, re-grease the housing, and check that the gate itself swings freely so the new gear isn’t doomed from day one.
• Linear control boards with failed relay contacts. The brains of the operation fail the same way on most Linear models, a relay that opens and closes a thousand times a year eventually burns its contacts. The symptom is a gate that opens fine but won’t close, or a keypad that works intermittently. We test the board before replacing it, because throwing a new board at a bad wiring connection is a waste of your money and our afternoon.
• Linear receiver range issues from antenna placement. This is common on the Linear Multi-Code receivers paired with older gate setups. The antenna gets tucked inside the metal housing, which kills the range to the point where the remote only works from forty feet away. We relocate or extend the antenna outside the housing, and suddenly the remote works from inside the house or from the street. A ninety-cent fix that changes how the gate feels to live with.
• Linear safety edge failures on sliding gates. Allen clay soil shifts with the weather, and a concrete pad that moves half an inch can pinch a safety edge against the gate track. The edge gets crushed, the gate won’t close, and the owner assumes the motor is dead. We replace the edge, shim the track, and in homes where the pad has moved enough to matter, we’ll tell you honestly that the right fix is re-setting the pad, not just swapping the edge every spring.

Our Linear Gate Installation Process

Every Linear gate installation in Allen follows the same steady sequence, settled before we ever touch a tool.

1. 1
   We talk first. You call (936) 274-8988, a live person answers, and we ask about your gate, your opener, and what’s going on at the driveway. We schedule a visit at a time that works for you.
2. 2
   Site inspection and honest measurement. We come out, measure the gate opening, check the posts for plumb, look at the driveway slope, and confirm the power situation. If the gate itself is still sound, we’ll tell you that outright. If it’s time to replace it, we’ll tell you that too, with numbers to back it up.
3. 3
   Upfront price, agreed before work starts. You get a written quote covering the labor, the Linear equipment, the hardware, and anything else the job needs. No surprises later. We settle the price before a single bolt is turned.
4. 4
   The installation. We hang the gate or set the operator, run the arm or the chain, wire the control board, install the safety edges and photo eyes, and tie in your remotes and keypad. We use OEM Linear parts when they’re the right call, and quality aftermarket parts when they match or exceed spec and save you real money. We’ll tell you which is which and why.
5. 5
   Test cycles and final walk-through. We cycle the gate twenty or thirty times, adjust the limits, test the safety reverse, and walk you through how everything works. We don’t leave until it’s right.
6. 6
   The 90-Day Done Right Promise, in writing. Every job gets our written guarantee. If anything isn’t right in the first 90 days, we come back and make it right. No paperwork, no arguing, no exceptions.

What Linear Gate Installation Costs in Allen

What moves the price in Allen is mostly the gate itself. A welded steel gate costs more than an aluminum one. A double gate needs two operators and twice the hardware. A gate going in on a slope needs more prep than one on flat ground. And power runs longer than about 100 feet add trenching and conduit work. We quote it all upfront, line by line, and the price doesn’t move after we shake on it. Call (936) 274-8988 for a free estimate. We also offer $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a standing 5% discount for seniors and veterans.

Why Allen Homeowners Call Ironworks Gate Co. for Linear Work

Victor Salinas, our owner, grew up right here in Allen, wandering the area around Watters Creek back when it was open Texas field, not a shopping center. He’s spent the better part of three decades working gates across Allen and the surrounding communities, and he built this company around one lesson he learned early: metal either holds or it doesn’t, let’s make sure yours does.

We’ve been at this since 1984, and we intend to be out here another forty years. That changes how we work. We don’t rush. We don’t guess. We service all nine major gate-automation brands, and if you ever move off Linear to a LiftMaster, Mighty Mule, Ghost Controls, or DoorKing system, the same technicians who know your gate will know your next operator too. Every technician who shows up at your door is background-checked and uniformed, and every single job gets our written 90-Day Done Right Promise. A live person answers the phone 24 hours a day, 7 days a week. If it isn’t right, we come back and make it right. That’s the whole deal.

FAQs