Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Installation in Allen: What to Know First
We install, replace, and service FAAC gate openers and operators on driveways across Allen, and most FAAC gate installations are completed within a few days of the first call, depending on parts. As an independent FAAC service provider, we’re not tied to the manufacturer, which means we quote the job honestly and stand behind the work with our own written 90-Day Done Right Promise. If you own a FAAC system and it’s failing, or you’re planning a new gate and want FAAC automation on it, this page tells you what to expect from us. Call (936) 274-8988 and you’ll get a live person, any hour.
How FAAC Products Fail - and How We Fix Them
FAAC builds a solid operator, and most of the ones we see in Allen have been in service for a long time. But every machine has its weak points, and knowing them ahead of time saves homeowners money. Here’s what we typically find on FAAC systems in this area:
- Capacitor failure on older FAAC 400 and 402 series. These swing-gate operators run on a capacitor-start motor, and when that capacitor begins to fail, the gate slows down, hums, or refuses to move on cold mornings. A technician who doesn’t know FAAC may blame the motor and quote a full replacement. We test the capacitor first, replace it when needed, and save the homeowner a thousand dollars or more.
- Limit switch drift on the FAAC 750 and 844 slide-gate models. The magnetic limit switches on these units can shift slightly over years of heat and vibration, causing the gate to stop short of full open or slam harder than it should at the end of travel. We reset and reposition the limits, then run the gate through a full cycle test to confirm it closes exactly where it should.
- Water intrusion in the control board housing. Allen sees real rain in spring and fall, and we regularly open FAAC cabinets to find corrosion on terminal strips and board connections. Water gets in through conduit fittings or aged gaskets, and it causes intermittent failures that look like a bad board but are often just a bad connection. We wire-brush, dielectric-grease, and seal the entry points so the problem doesn’t come back.
- Gearbox wear on the FAAC C720 and S418 slide operators. These units use a reduction gearbox that can develop play over years of daily cycling. You’ll hear it as a clunk when the gate starts or reverses. We replace the worn gears with OEM-equivalent parts and re-grease the box, which restores smooth operation without the cost of a new operator.
- Battery backup neglect on FAAC systems with the optional 24V buffer. FAAC’s battery backup keeps the gate working during power outages, which matter in Allen when storms knock out power. Those batteries have a service life of 3 to 5 years, and when they die quietly, the homeowner doesn’t know until an outage proves it. We test and replace backup batteries during installation and tune-ups so the gate never leaves you locked out or locked in.
Our FAAC Gate Installation Process
A FAAC gate installation is not a guess-and-check job. We measure, plan, and execute in a specific order, and you’ll know the price before we turn a single bolt.
- 1
Call and describe your gate. You call (936) 274-8988. We ask about your gate type, the operator model if you know it, and what it’s doing or not doing. No script, no phone tree.
- 2
On-site inspection and measurement. We come to your Allen property, measure the gate leaf, check the hinges and posts, and examine the existing FAAC operator or the mounting surface for the new one. We look for what’s failing, but also for what’s about to fail.
- 3
Written quote before any work. We give you a price for the parts and labor, agreed upon up front. No surprises on the bill, ever. That’s how we’ve done it since 1984.
- 4
Parts decision. We use FAAC OEM parts where they matter for warranty and fit, and quality aftermarket equivalents where they perform just as well for less. We tell you the difference and let you choose.
- 5
Installation and testing. We mount, wire, program the limits, and set the safety features. Then we cycle the gate forty or fifty times, check the force settings, and verify the auto-reverse and obstruction detection work correctly.
- 6
Cleanup and walkthrough. We leave the site as we found it, show you how to operate the system, and hand you the written 90-Day Done Right Promise on the work.
What FAAC Gate Installation Costs in Allen
FAAC gate installation in Allen runs a real range, and the price depends on what you have and what you need. A new FAAC 400-series swing-gate operator installed on an existing, healthy gate typically lands between $1,800 and $3,400 depending on gate weight and access. Replacing a failed control board or limit switch assembly on a FAAC slide operator is usually $450 to $1,200 including labor. A full system replacement with new operator, brackets, safety edges, and wiring on a sliding driveway gate commonly runs $3,500 to $7,500. What moves the price is gate size, post condition, conduit placement, and whether we’re adding battery backup or access control. Call (936) 274-8988 and we’ll give you a free estimate before any work starts.
Why Allen Homeowners Call Ironworks Gate Co. for FAAC Work
Victor Salinas grew up in Allen, back when Watters Creek was open Texas, and he’s spent nearly three decades working gates across this town. He studied welding and industrial mechanics at Collin College in McKinney, where an instructor told him metal either holds or it doesn’t, and that stuck. It’s why every FAAC job we do goes through the same deliberate process the 400th time as the first. We’re trained and equipped on nine automation brands, so if your FAAC isn’t the right fit anymore, we can speak honestly about LiftMaster, Mighty Mule, Ghost Controls, or DoorKing instead of forcing a brand decision that doesn’t serve you. Live phone support, 24/7. Background-checked, uniformed technicians. And every job backed by the 90-Day Done Right Promise in writing. Metal either holds or it doesn’t. Let’s make sure yours does.
FAQs
We are an independent FAAC service provider, not an authorized warranty station, so FAAC factory warranty claims go through the manufacturer. What we do provide is our own written 90-Day Done Right Promise on every FAAC installation and repair we complete. If it isn’t right, we come back and make it right, no paperwork and no argument. Call (936) 274-8988 for the specifics on your system.
Most FAAC gate installations in Allen are scheduled within a few days of the first call, and if the parts are on our truck, we often finish the job in a single visit. If a specific FAAC board or gearbox needs to be ordered, we’ll tell you the timeline up front and quote the job before ordering anything.
If your FAAC operator is under fifteen years old and the failure is a capacitor, limit switch, or board-level component, repairing it usually makes more sense than replacing it. If the gearbox is worn and the gate leaf is heavy, a new operator may be the better long-term move. We’ll give you both prices and an honest recommendation.
Yes, we install FAAC automation on existing driveway gates, swing gates, and sliding gates regardless of who fabricated the gate. We check the hinges, posts, and gate balance first because a poorly hung gate will eat even a good operator. If the gate needs welding or hinge work first, we handle that in the same visit.
Yes, estimates are free, and the price we quote is the price you pay, agreed before any work starts. Call (936) 274-8988 and you’ll get a live person, not a voicemail tree.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Allen and nearby areas.