Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Parker
Gate installation in Parker almost always means one thing: a long private driveway, a heavy iron gate, and an opener that has been out in Collin County weather for twenty years. New construction is rare here because of the 1-acre minimum zoning, so most of our work is replacement and retrofit, not fresh installs on bare land. That changes the questions worth asking. Our crews work Parker every week, know the clay soil and the housing stock, and quote every job in writing before we turn a bolt. Call (936) 274-8988 and a live person picks up, day or night.
Why Ironworks Gate Co. Is Parker’s Preferred Gate Installation Company
We have been doing gate work for over 42 years. In Parker specifically, that history matters because most of the gates we touch were hung in the 1990s and early 2000s, and we know those installations, those operators, and the ways they fail here. Homeowners off Country Club Drive, Crown Ridge, and Douglass Road call us because their neighbor recommended us, not because they clicked an ad. We keep it that way.
Our technicians are background-checked and uniformed. They show up when we say they will. And before any Gate Installation begins, you get an upfront written price. No surprises on the bill. Every job is covered by our written 90-Day Done Right Promise, the Keystone Standard: if it is not right, we come back and make it right. No paperwork, no arguing.
Victor Salinas leads our crews. He has trained our people on nine automation brands, and he stands behind every job that leaves our shop, including every gate we install in Parker and the surrounding Collin County area.
Our Gate Installation Services in Parker
Driveway Gate Installation
A driveway gate in Parker is rarely a weekend project. Minimum 1-acre lots mean driveway runs of 80 to 300 feet, often curved, always sloping somewhere. We measure the grade, check the set back, and plan the operator location so the gate opens cleanly on day one and ten years from now. Most driveway gate installations in Parker run $4,800 to $11,500 for a complete new steel swing gate with operator, depending on width, weight, and access control. That price is quoted before work starts.
Pedestrian Gate Installation
Pedestrian gates get overlooked until the main driveway gate is automated and someone realizes the walk gate still drags or no longer latches. Around estates on Running Brook Drive and Tall Tree Lane, we match the new pedestrian gate to the existing driveway gate’s steel and finish. A basic steel walk gate with frame and hardware in Parker typically runs $900 to $2,400 installed, more if custom ironwork is required to match an existing pattern.
Sliding Gate Installation
For long driveways with limited swing clearance, a cantilever slide gate is often the right answer. Parker lots with circular drives or gates set close to the property line along Douglass Road frequently need this configuration. A sliding gate installation in Parker with a new operator generally runs $5,500 to $13,000. We include the track, rollers, safety photocells, and operator, all quoted in writing before the first day of work.
Swing Gate Installation
Swing gates are the most common gate in Parker because they fit the estate look most homeowners want: two ornamental iron leaves meeting at the center, hung on brick or stone piers. New double swing gate systems in Parker, including both panels and a dual operator, run $6,200 to $14,800. Single swing gates run less. The critical work is the hinge post footing, which is exactly where the clay does its damage, and we do not skip that step.
Double Gate Installation
Double gates carry the most weight and the highest failure rate, especially on Parker’s heavy wrought iron originals. Each leaf can weigh 400 to 900 pounds. When we install a double gate in Parker, we set both hinge posts in extended concrete piers, then calibrate both operators so they open and close in sequence without dragging. The written price accounts for all of it, from concrete to control board.
Security Gate Installation
A security gate in Parker is as much about keeping horses in and unwelcome vehicles out as it is about curb appeal. We install gates with keypads, vehicle detection loops, and intercom options. Many Parker homeowners with live stock on 3-to-5-acre parcels off Old Custer Road need a gate that operates on a timer and holds up to daily cycles. A security-focused installation with access control typically runs $5,800 to $14,500, depending on the operator and entry system you choose.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Parker
We are trained and equipped on nine gate-automation brands, and in Parker we work most often on LiftMaster, FAAC, BFT, Linear, Viking, and Ghost Controls systems. Older Parker gates from the 1990s frequently carry original LiftMaster or Elite operators, and we still stock parts and boards for many of those legacy units. If your existing operator is worth keeping, we tell you plainly. If it is not, we recommend the right replacement from a brand we service daily, and we quote it before any work begins.
Common Gate Installation Problems We See in Parker Homes
- Clay heave on the hinge post. Collin County black clay swells and shrinks with every wet and dry cycle. On Parker’s long iron swing gates, the hinge post and its footing get worked out of plumb over one to three seasons, and then the gate drags on the latch side. Re-setting that post in a deeper concrete pier extension is the fix; re-aiming the operator alone is a callback.
- Obsolete control boards with no entrapment protection. Many original 1990s operators in Parker predate modern UL 325 safety standards. They may still run, but they lack the safety reverses and monitored photocells that current installations require. Retrofitting a new board is sometimes possible; replacing the entire operator is often cheaper than nursing a 25-year-old board through another summer.
- Cracked wiring insulation from 105-degree heat. Low-voltage wiring along Parker driveway runs sits in full sun for hours daily. Insulation gets brittle and cracks. Then a retrofitted safety photocell faults intermittently and drives a homeowner crazy. We replace the low-voltage run when we install the gate, not just the components that failed.
- Heavy iron gates overloading original footings. A 16-foot ornate iron gate from 1998 could weigh 800 pounds. Its original footing may have been marginal when new. After 25 years of wet and dry cycles, it is under-sized. Before we mount any new operator, we inspect the footing, and if it is undersized we extend the concrete pier. This is the step that separates an installation that lasts from one that sags in two years.
Pricing for Gate Installation in Parker, TX
New gate installation in Parker runs from about $900 for a simple steel pedestrian gate up to $14,800 for a full security-grade double driveway gate with automation and access control. You are likely falling somewhere in between: a new single swing driveway gate with operator and keypad in Parker typically costs $4,800 to $8,700. A new double swing gate with dual operators runs $6,200 to $14,000. A cantilever slide gate with track, operator, and safety edges runs $5,500 to $13,000. All of it is quoted before we start, and the price we quote is the price on the invoice. We offer a free estimate on any new installation, $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a standing 5% discount for seniors and veterans. Call (936) 274-8988 and we will measure your driveway and give you a number in writing.
We Also Serve Cities Near Parker
Our crews cover Parker and surrounding Collin County communities including Allen, Plano, Fairview, and Lucas. If you live just outside Parker city limits, call us. We will tell you honestly whether we can reach you and when, and we will quote the job the same way we quote every job: in writing, before any work begins.
Serving Parker, TX - Our Local Coverage Area
We’re based in the Parker area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Parker
Most 1990s LiftMaster operators on Parker estate gates cannot be retrofitted to meet current UL 325 standards because the control board lacks the inputs for monitored safety devices. In some cases, a new aftermarket control board and safety photocells can bring an older mechanical unit up to code, but the wiring in Parker, exposed for 25-plus years to 105-degree summers, often has cracked insulation that makes a retrofit unreliable. We will tell you which path is cheaper and safer after we open the unit and look. Call (936) 274-8988 for an honest assessment and a written quote.
Yes, in many Parker locations a cantilever slide gate is the better long-term answer. A slide gate rides on a track or cantilever rollers, so it does not rely on hinge post footings, which are the first thing the clay heaves out of plumb. If your driveway has room for the gate to slide to one side and the grade is reasonably level, a slide gate avoids the single most common failure we see in Parker: a heavy swing gate pulling its hinge post over after repeated wet and dry cycles. The trade-off is that a slide gate costs more up front and requires annual track cleaning. We quote both options so you can decide with real numbers.
We cut the hinge post free, re-set it plumb in a deeper concrete pier extension, re-hang the gate leaf, and then re-calibrate the operator and re-aim the safety photocells. In Parker, the drag is almost always worse on the hinge post than the latch post because the weight of a 12-to-16-foot iron gate leaf pushes all the ground stress into that single anchor point. We have done this on estates off Country Club Drive and throughout Parker. If the gate leaf itself has warped from years of dragging, we also straighten or reinforce it before re-hanging. Call (936) 274-8988 and we will come measure the sag and quote the fix.
You do not have to reuse the same brand. A dead US Automatic operator on a Parker estate gate can be replaced with a Viking, Ghost Controls, LiftMaster, or any of the nine brands we service daily. The right replacement depends on the gate’s weight, length, and duty cycle. We carry parts and operators for all the major brands, and we will recommend the one that fits your gate and your usage, not the one we happen to have on the truck. The new operator comes with a written 90-Day Done Right Promise, and we include the safety edges and photocells that current code requires.
You can keep them. The ornate wrought iron panels from Parker’s 1990s estate building boom are generally worth keeping. They are heavier than modern production panels, but the steel is often thicker and the scrollwork is one-of-a-kind. We re-set the hinge posts in extended concrete piers, re-hang the existing panels, and swap the operator for a current model with proper entrapment protection. If the panels have rusted through at the bottom rail or the welds have cracked, we repair and reinforce before re-hanging. Replacing the entire gate is only necessary when the panels have corroded beyond structural soundness, which happens less often than people expect. Call (936) 274-8988 and we will inspect your panels and tell you straight whether they need repair or replacement.
On a 2.5-acre estate off Country Club Drive, our crew reset a 14-foot iron swing gate whose hinge post had heaved 2 inches out of plumb after a wet spring. The original LiftMaster operator was still functioning, but we cut and re-set the hinge post in a deeper concrete pier extension, then remounted the arm and re-aimed the safety photocell. The gate now closes squarely without the three-second drag it had before.
If your gate is dragging, failing, or simply old enough to vote, call us at (936) 274-8988. We will answer the phone, listen to what the gate is doing, and schedule a time that works. Estimates for new gate installation in Parker are free and written. We stand behind it.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Parker and surrounding Collin County for over 42 years.